 |
See Technical Specs for details on TPI-712 upgrade kits
Accurately test flue gases in furnaces and domestic boilers to determine operation efficiency. Time/date documentation for future reference.
- Measures CO, O2, pressure, and temperature
- Calculates CO2 and gross or net efficiency
- Works on High Efficiency furnace
- Select between 4 fuels (Natural Gas, LPG, Light Oil, Heavy Oil)
- Pump driven for fast response
- Dual input differential manometer with 3 selectable units of measure: kPa, mBar, inH2O
- Flue probe with built-in thermocouple
- IR printer port - use optional A740 Infrared Printer
- Soft carrying case
- Protective rubber boot
Applications:
|
RESIDENTIAL
- Furnace
- Hot water heater
- Radiant heat boilers
- CO testing
|
COMMERCIAL
- Boilers
- Furnaces
- Hot water heater
- CO testing
|
INDUSTRIAL
- Boilers
- Furnaces
- Hot water heater
- CO and high CO testing
|
Measure and Memory:
- CO
- Range: 0-10,000ppm
- Resolution: 1ppm
- Accuracy: ±5ppm or 5%, whichever is greater
- O2
- Range: 0-25%
- Resolution: 0.1%
- Accuracy: ñ0.3%
- CO2
- Range: 0-25%
- Resolution: 0.001
- Accuracy: Calculated
- Excess Air (Calculated)
- Efficiency (Calculated)
- Leak (Level)
- Pressure (Difference)
- Temperature (2-Channel): -100° - 1,000°C
- Difference (Ch1-Ch2 Calculated)
- Single Memory Store: 10
- Data Logger 100 Steps x 4 Page
- Recall Function
- Real Time Display
- Backlight
- IR Print Port
- Store Mode Print
- Real Mode Print
- IRDA
|
Specifications:
- Operating Temperature Range: -10ø to 50øC (14ø to 122øF)
- Battery: 4AA Alkaline Batteries
- Fuels: Natural Gas, LPG, Light Oil, Heavy Oil
- Display: Backlit LCD T
- Time & Date: 24 Hour Real-Time Clock
- Dimensions: 200mm x 90mm x 60mm
- Weight: 500g
- Switch Off: Failsafe
- Exhaust: Safety Spigot
- Conforms To: BS7927 (and the draft BS7967)
Included with all models:
- Carrying Case
- Flue Probe
- Protective Boot
- Manual
|
TPI-712C5 Kit
Includes TPI-712 and TPI-270
TPI-712A740 Kit
Includes TPI-712 and TPI-A740
TPI-712C7 Kit
Includes TPI-712, TPI-270 and TPI-A740
TPI-270
APPLICATIONS
-
Thermocouples in furnace and gas appliances
-
Heat anticipator current in thermostats
-
Line voltages
-
Control Voltages
-
Flame safety control current
-
Heating element resistance
-
Compressor winding resistance
-
Contractor and relay coil resistance
-
Motor and compressor startup current
-
Motor run and start capacitors
-
Bar graph indicator of rapid fluctuations
-
Continuity of wiring
-
Measure frequency on control and line voltage
-
Record minimum and maximum of measurements
-
Measure temperature
-
Measure true RMS of distorted or non-linear signals
-
Measure line current
-
Test continuity of circuit breakers and fuses
-
Measure voltage of direct drive DC motors
-
Measure power supply voltage
-
Measure power supply current
-
Non-contact Voltage Detection
SPECIFICATIONS
DISPLAY SPECIFICATIONS
-
4,000 count
-
Analog bar graph
BASIC FEATURES
-
AC volts
-
DC volts
-
AC amps
-
DC Microamps (using the test leads)
-
Resistance
-
Diode test
-
Audible continuity
ADDITIONAL FEATURES
-
Frequency
-
Capacitance
-
Temperature
-
Non-Contact voltage detection
-
Data hold
-
Relative Mode
-
Min/max/peak
-
Peak hold
-
Sleep mode/Auto off
RANGE AND RESOLUTION
-
Basic DC Accuracy: .5%
-
DC Voltage (maximum): 600V
-
Resolution (maximum): 0.1mV
-
AC Voltage (Maximum): 600V
-
Resolution (maximum): .1mV
-
DC Amps (maximum): 400µA
-
Resolution (maximum): .01µA
-
AC Amps (maximum): 400mA
-
Resolution (Maximum): .01 A
-
Resistance (maximum): 40MΩ
-
Resolution (maximum): 0.1Ω
-
Frequency (maximum): 400MHz
-
Resolution (maximum): .001KHz
-
Capacitance (maximum): 40,000°F
-
Resolution (maximum): .001nF
-
Temperature (maximum): 1000°F
AGENCY APPROVAL
-
CE IEC 1010: CAT III 600V
-
cULus 3111: Pending
TPI-A740 IR Printer
-
Self test at power on
-
Adjustable contrast
-
Uses common thermal paper
-
Manual paper advance
|
|
|