 |
 |
 |
|
SKF TIH 03m/230V Small Induction Heater | Small induction heater with a 40 kg bearing heating capacity - 200–240 V/50–60 Hz. Schuko-type plug
- Compact lightweight design; just 20,9 kg (46.0 lb) facilitating portability
- 2-step power setting and smaller yokes allow heating smaller bearings safely and at lower power consumption>
- Capable of heating a 28 kg (61.7 lb) bearing in just 20 minutes
- Temperature mode pre-set at 110 °C (230 °F) to help prevent bearing over-heating
- Automatic demagnetisation
- This induction heating system is warranted for 3 years
- Schuko-type plug included. May need to be replaced by customer, depending on local-service receptacle type
|
The SKF small induction heater TIH 030m combines high heating capacity with portability. The compact lightweight design makes the TIH 030m portable. Placing the induction coil outside the heater's housing allows the heating of bearings weighing up to 40 kg (88 lb). The induction heater is equipped with thermal overheating protection to reduce the risk of damage to the induction coil and the electronics. In addition to temperature mode, the TIH 030m is equipped with a time mode for heating components other than bearings. The induction heating system is supplied standard with three yokes and is available in two executions: 230V/50-60Hz and 100-110V/50-60Hz.
 Data Sheet
SPECIFICATIONS:
(TIH 030M/230V and TIH 030M/110V):
- SKF m20 performance: 28 kg (61.7 lb)
- Voltage, V/Hz: 230V/50-60Hz or 100-110V/50-60Hz
- Work piece:
- Maximum weight: 40 kg (88 lb)
- Maximum bore diameter: 20 - 300 mm (0.8 - 11.8 in)
- Temperature control:
- Range: 0 - 250 øC (32 - 482 øF)
- Magnetic probe: Yes, K-type
- Accuracy: (electronics) ñ 2 øC (ñ 3.6 øF)
- Time control:
- Range: 0 - 60 minutes
- Accuracy: ñ 0,01 sec.
- Maximum temperature (approx.): 400 øC (750 øF)
- Thermometer mode: Yes
- Bearing mode: Yes
- Power setting: 2-step; 50% or 100%
- Demagnetisation according to SKF norms (automatic): Yes (<2 A/cm)
- Can heat sealed bearings: Yes
- Can heat pre-greased bearings: Yes
- Error guiding codes: Yes
- Thermal overload protection: Yes
- Control panel: Control panel and LED display integrated in remote controle
- Operating area: (w x h) 100 x 135 mm (3.9 x 5.3 in)
- Coil diameter: 95 mm (3.7 in)
- Dimensions: (w x d x h) 450 x 195 x 210 mm (17.7 x 7.6 x 8.2 in)
- Total weight, including yokes: 20,9 kg (46.0 lb)
- Maximum power consumption: 2,0 kVA
- Standard yokes:
- 45 x 45 x 215 mm (1.7 x 1.7 x 8.4 in), for heating bearings with bore diameter of 65 mm (2.6 in) and larger.
- 28 x 28 x 215 mm (1.1 x 1.1 x 8.4 in), for heating bearings with bore diameter of 40 mm (1.6 in) and larger.
- 14 x 14 x 215 mm (0.5 x 0.5 x 8.4 in), for heating bearings with bore diameter of 20 mm (0.8 in) and larger
- Core cross section: 45 x 45 mm (1.7 x 1.7 in)
- Bearing support arms: Yes, foldable
- Yoke storage: Yes, internal integrated in foldable bearing support arms
- Cooling fan: No
- Swivel arm: No
- Housing material: Steel and glass filled polyamide
- Warranty period: 3 years
|
|
|
 |
|
 |
|